View FPD-010R008-0E_3692346.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 1 of 13 o-microgigacn? 4-channel optical transceiver module part number: module: FPD-010R008-0E patch cord: foc-cc**** description newly developed optical transceiver module, fujitsu s o-microgigacn? series supports electric to optical interface conversion and provides 3.125 gbp s x 4 channel, bi-directional data transfer. the el ectrical interface is fujitsus industry standard high-speed differential copper connector, microgigacn? that h as been selected by infiniband?, 10g fiber channel, 10 gbase-cx-4, sas, and sata2. the o-microgigacn? module makes it possible to exte nd transmission length up to 300m (2.5gbps) over fiber optic cable from industry standard 4 lane cop per cable with media detection circuitry (connector detect and power supply circuitry) on the customers board /host side. the module provides flexibility, allowi ng the user to select interface options with the one low c ost copper i/o connector on the board. the module p rovides a low cost solution for data center requirements. features converts 4x microgigacn? to 4x optical interface optical interface 12-channel mpo connector up to 100m links with standard 50/125um mmf ribbon cable at 3.125 gbps, and up to 300m at 2.5 gbps reliable, low cost 850nm vcsel technology 0 to +70 degree c case temperature operating range low power: 0.9 watts typical with 3.3v power supply supplied through connector hot pluggable electrical interface iec class 1m laser eye safty compliant
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 2 of 13 block diagram electrical optical figure 1: functional block diagram absolute maximum rating stress beyond the values stated below may cause pe rmanent damage to the device. exposure to absolute maximum rating conditions for extended periods may affect device reliability. table 1 absolute maximum rating parameter minimum maximum units notes storage temperature -20 +85 relative humidity 5 85 % supply voltage 3.14 3.47 v input stage vcsel driver vcsel array data in ch 1-4+ data in ch 1-4- data out ch 1-4 output stage pd driver pd array data out ch 1-4+ data out ch 1-4- data out ch 1-4
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 3 of 13 recommended operating conditions table 2: operating conditions parameter minimum typical maximum units notes operating case temperature 0 +70 supply voltage : vcc 3.14 3.3 3.47 v power dissipation 0.9 w power supply noise 200 mv p-p 1 transmitter differential input voltage 100 1600 mv p-p signaling rate/channel 0.5 3.1875 gbps 2 serial data input termination 50 notes: 1. transmitter differential input voltage = (vin+p- p) C (vin-p-p) 2. limits assume prbs2 23 -1. signaling rates lower than indicated may be use d with encoding schemes such as 8b/10b coding. electrical characteristics table 3: transmitter electrical characteristics (operating temperature: +20 to +80 , power supply: 3.14v to 3.47v) parameter minimum typical maximum units notes transmitter differential input voltage 100 1600 mv p-p odiscontrol voltage -high vcc-1.3 vcc v 1 odis control voltage -low 0.8 v 1 notes: 1. all vcsel transmitters are enabled when this sig nal is high.
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 4 of 13 table 4: receiver electrical characteristics (operating temperature: +20 to +80 , power supply: 3.14v to 3.47v) parameter minimum typical maximum units notes differential peak-to-peak output voltage swing 450 800 mv 1 data output rise time 60 150 ps 2 data output fall time 60 150 ps 2 contributed deterministic jitter 54 ps contributed total jitter 112 ps notes: 1. outputs are compatible with 10k, 10kh, 100k ec l and pecl inputs. 2. electrical rise/fall time is measured at 20% a nd 80% of the receivers serial digital output. optical characteristics table 5: transmitter optical characteristics (operating temperature: +20 to +80 , power supply: 3.14v to 3.47v) parameter minimum typical maximum units notes output optical power -2.0 dbm avg. 1 optical modulation amplitude 0.19 mw 2 wavelength 830 850 860 nm spectral width Crms 0.85 nm data output rise/fall time 130 ps 3 inter-channel skew 0 100 ps relative intensity noise (oma) -120 db/hz contributed deterministic jitter 40 ps contributed total jitter 100 ps 4 notes: 1. optical power measured at the end of 1m 50/125 m fiber with numerical aperture = 0.2. the specifie d optical output power will be compliant with iec 608 25-1 a2, class 1m accessible emission limits. 2. optical modulation amplitude (oma) is provided to specify link performance. oma can be related to average power and extinction ratio using the graph in figure 1. the minimum er emitted by the transmitter is 4 db. 3. these are unfiltered 20-80% values. 4. total contributed jitter (tj) is given assumin g detected bit-error ratio equal to 10 -12 .
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 5 of 13 table 6: receiver optical characteristics (operating temperature: +20 to +80 , power supply: 3.14v to 3.47v) parameter minimum typical maximum units notes input optical power -2.0 dbm avg. 1 wavelength 830 850 860 nm return loss 12 db 2 signal detect asserted -17 dbm avg. signal detect de-asserted -30 dbm avg. unstressed receiver oma -13 dbm 3 stressed receiver oma -10 dbm 4 notes: 1. measurement using 1m optical loopback between optical transmitter and receiver. 2. return loss is defined as the minimum attenuat ion (db) of received optical power for energy refle cted back into the optical fiber. 3. unstressed receiver oma is the largest optical modulation an ideal signal with no shape or noise penalties has to have at the input of the receiver in order t o produce detection with bit-error ratio of at most 1.0e-12. 4. calculated assuming a compliance signal that e xhibits 1 db vertical eye closure penalty, peak-to- peak source deterministic jitter dj=60ps, and duty-cycle distortion component of deterministic jitter equal to dcd=22ps, no amplitude noise and no random jitter. stressed receiver oma is the optical modulation amplitude of the compliance signal at the input to the receiver that results in data detection with bi t-error ratio better than 10 -12 . laser eye safety the transceiver module comply with laser product c lass 1m laser eye safety requirements per iec/rn 60825-1 amendment 2: 2001. led indicator led indicator as following table 7. table 7: led indicator led light up status not light up the power is not supplied. green light up power on and the connector is workin g. green and red light up the connector is not working . (link error.)
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 6 of 13 link overview optical link carries a duple 4x link as shown in f igure 2. link distance the following table 8 lists the reach distance of the o-microgigacn? for different multi-mode (mmf) t ypes and bandwidths. each case includes a maximum of 2 d b per channel connection loss for path cables. table 8: link distance data rate mmf type 62.5/125 m 150mhz.km 50/125 m 500mhz.km 50/125 m 2000mhz.km 2.5 gbps / channel 100m 300m 500m 3.125 gbps / channel 50m 100m 300m optical fiber cable optical fiber cable optical fiber cable optical fiber cable microgigacn tm 12 1 electrical (cx4 or ibta) lane0 lane1 lane2 lane3 receiver transmitter lane3 lane2 lane1 lane0 4 lane free fiber figure 2: o-microgigacn? link overview o-microgigacn tm host microgigacn tm mpo connector mpo connector optical
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 7 of 13 optical fiber cable specification the following table 9 the optical fiber cable speci fication for o-microgigacn tm . table 9: optical fiber cable specification link performance the link distance in table 7 shall be achieved wit h the following table 10. table 10: link performance parameter value unit bit error rate (ber) < 10 -12 bit item value note connector type mpo/mtp polishing flat polishing polarity without pin channel 12 channels fiber type multi mode, 50/125 m, gi, ribbon type insertion loss 1.0db max transmission band 500mhz*km or 2000mhz*km
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 8 of 13 supply power to the o-microgigacn? the microgigacn? usually does not provide power fo r the module. the draft proposal of fc-pi-2 allows the re-assignment of some ground pins as power pins, as shown in the following table 11. this re-assignment does not affect the function or performance of standard cable connection for infini band? and 10gbase-cx4 applications, as the power is added only when the system is sure the attached module i s active. the re-assigned pins are all ac ground to minimize the effect on high-speed signal integrity . table 11: pin assignment in fc-pi-2 connector pin number alternate signal definitions g1 signal ground g2 odis g3 signal ground g4 signal ground g5 signal ground g6 fault- g7 type_sense g8 vcc g9 signal ground s1 rx0+ s2 rx0- s3 rx1+ s4 rx1- s5 rx2+ s6 rx2- s7 rx3+ s8 rx3- s9 tx3- s10 tx3+ s11 tx2- s12 tx2+ s13 tx1- s14 tx1+ s15 tx0- s16 tx0+ housing chassis ground
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 9 of 13 fujitsu component recommends the following figure 3 on customers board to perform the media detect function. the circuitry uses less than 1/4 s quare inch of board space on a single layer, and us e less than 1ma of current. figure 3: recommended mdc
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 10 of 13 odis (optics disable) -input-: disable the optics w hen this signal is pull high. enables the optics when this signal is pull low. if it is tied to gnd then the optical transmitter is default on when power is applied. fault- (tx_fault indicator) Copen drain output-: it is default high, and will turn low when there is a fault. shorting this pin to ground will not af fect the performance of the module. the recommended parts are listed in the following table 12. table 12: recommended parts of mdc item designator description qty maker part number 1 u1 dual push-pull output comparator 1 maxim max9032aka 2 r2 5.1k 0402 resistor 1 3 r1 10k 0402 resistor 1 4 r3, r5 3.9k 0402 resistor 2 5 r4 6.8k 0402 resistor 1 6 c3, c4, c5 0.01 uf ceramic 0402 capacitor 3 7 u2 single 2-input positive-and gate 1 ti sn74ahc1g08dckr 8 u3 power distribution switch 1 ti tps2031d 9 c2 0.1 uf ceramic 0402 1 10 c1 10 uf tantulam case b capacitor 1 11 cn1 microgigacn tm 1 fujitsu
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 11 of 13 product family module part numbers description FPD-010R008-0E 8pear microgigacn tm and 12-channel mpo/mtp connector support mechanical design of o-microgigacn? is shown as fol lowing figure 4. it is preliminary design and subject to change with out notice, please check with us for the latest des ign. figure 4: o-microgigacn? schematic drawing
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 12 of 13 patch cord part numbers description foc-cc1**** 12-chanel mpo fiber optic patch cord - mmf 50/125um 500mhz/km, ruggedized type of patch cord, without guide pin part numbers standard length foc-cc10001 1m foc-cc10002 3m foc-cc10003 5m foc-cc10004 10m foc-cc10005 15m foc-cc10006 20m foc-cc10007 30m foc-cc10008 40m foc-cc10009 50m foc-cc10010 70m foc-cc10011 100m foc-cc10012 150m foc-cc10013 200m foc-cc10014 300m figure 4: patch cord schematic drawing
o o - - m m i i c c r r o o g g i i g g a a c c n n ? ? data sheet revision 4.2 fujitsu component limited page 13 of 13 revision date changes rev 0.0 may 5, 2004 document creation. rev 1.0 july 23, 2004 revised all pages. rev 2.0 dec 27, 2004 revised all pages. rev 3.0 jan 12, 2005 revised all pages. rev 4.0 mar 2, 2005 revised 1, 11 page. part number change. rev 4.1 apr 28, 2005 revised 1 page. figure. rev4.2 jun 22, 2005 revised 7 page. addition optica fiber specification.

▲Up To Search▲

Price & Availability of FPD-010R008-0E

	To Download FPD-010R008-0E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .